Description

Functions introduccion
- Call apartment
- Open door, relay delay settings
- Connect exit button
- Speech message for release lock
- Door opened alarm
- Tamper alarm
- Alarm management by access control (only panel with proximity reader)
- Work mode
Call apartment
Visitor push the pushbutton for calling in the 1W Panel, the ring back tone will be sent, meanwhile the monitor will ring. The monitor will show video and can conversation after answer, then release lock.
Web browser programming
The 1W panel has an integrated web server, which allows to configure the parameters. This web server is accessed via the panel’s IP address.
The browser opens with the configured IP address of the panel. A screen opens requesting a username and password.
- Default IP: 10.1.1.2
- Username: admin
- Password: 123456
Device
The following information is displayed: device name, firmware version, MAC address, IP address about the panel.

General
The section GENERAL allows the configuration of the identification parameters of the 1W MILO panel within the installation.
It allows time-date configuration.

TYPE: Select the identification parameter of the panel. There are some other parameters related, depending on TYPE selection.
General entrance panel
Panel installed in one of the main entrances to a condominium.

- CONGIERGE: The number of concierges can be assigned to each concierge from 9901 to 9998, depending on the installation.
Block panel entrance
Panel installed in a single building or in a block of a condominium.

- CONGIERGE: The number of concierges can be assigned to each concierge from 9901 to 9998, depending on the installation.
1 Way panel
For a single house or apartment. It can only call to a unique apartment.

VIDEO RESOLUTION: To fit the different types of monitors. The default value 640×480
PANEL VOLUME: Select a value between 1 and 5 to adjust the panel's audio output. The default setting is 4.
This volume level affects the voice synthesis, and notification tones.
Conversation volumen is autoadjusted.
If the project has no management software the installer can set date, time and time zone manually. If the project has management software, the date and time of panel will synchronizes automatically with the management software. If the panel has access to internet, the date and time of panel will also synchronize with internet time server.
NOTE:
1.TIME ZONE is usable only when the time is automatically taken from internet or FERMAX MANAGEMENT SOFTWARE.
2. Date and time can’t be saved after power loss, the time zone and date format can be saved.
3. The webserver will show “TOTAL: XXX RECORD(S) IMPORTED” when the language file is be imported.
Network configuration
If a device has an IP address already assigned to another device on the network,
Both devices will not work properly until this issue is resolved.
Access
DOOR RELAY TIME: Time for lock-release relay remains active (1-9s optional).Time for lock-release relay remains active (1-9s optional).
ADMIN CARD: Admin/master card ID registered to enrol additional prox cards. This option is useful when there is not MEET MAGEMENT SOFTWARE available.
When there is no management software, enter 0000 if you do not know the ID of the admin card. The first MIFARE prox card detected by the reader will act as admin/master card. The card of the residents can be added afterwards.
To program user cards, present the admin/master card previously created on the card reader. The panel will enter in cards program mode. All the cards presented from now on will automatically updated in the panel and may be used to open the door.
If there are not more cards to program, after two minutes the panel will exit program mode.
There is not possible to deregister cards programmed by this method. Use the FERMAX MEET MANAGEMENT SOFTWARE for full operational possibilities.
DISARM BY CARD:When an already programmed user card is presented to the reader, and it has been previously assigned to a monitor, the alarm system of the corresponding apartment will change to HOME mode.
ACCESS PIN: No function.

IP Camera
SIP
This option allows to configure 1W panel to use SIP functions, such us call divert to smartphone using the FERMAX MEET ME APP or allows the panel to operate with a third-party SIP systems or terminals using SIP protocol instead of FERMAX MEET protocol.
ENABLE SIP: Select this box to enable SIP functions.
SEARCH SIP STATUS: this button appears when enabling SIP function, shows SIP REGISTERED if the panel register successfully or SIP REGISTER FAILED if the panel register unsuccessfully.
SIP SERVER: Indicate the sip SERVER address. Format -> sip: IP_SERVER
DOMAIN: domain of the SIP server or IP address.
STUN IP: domain of the SIP server.
STUN PORT: Used for the configuration of Internet SIP server-based installations. It is usually port 5060. Check with your network or SIP server administrator.
TRANSPORT: UDP, TCP, TLS options. Default UDP, the No. port of UDP is 5060, the default port is 5060 if no port at the back sip:sip.fermax.com, the No. port of UDP is 5223, the No. port of TLS is 4443
SIP USER, SIP PASSWORD: Indicate the user and password that this terminal is programmed in the SIP server.
CONVERSATION, RING TIME: No function.
NOTE: When the panel is used as a sip device, use quick dial to call SIP devices or receive calling of other SIP devices, SIP function must be enabled.

SIP Call
APARTMET: The panel calls the resident.
NUMBER: The monitor, the call divert APP and sip device.
DELETE: Delete Apartment and number.

Advanced
Quick dial is associated a monitor, guard unit or sip terminal.
QUICK DIAL: Enable or disable quick dial function.
NOTE: The quick dial work when the panel is general panel or block panel, the panel do not call concierge.
URL: If call device of MEET system, URL: sip: sip account @ IP address of MEET device, the sip account is optional. If call SIP device, URL: sip: sip account @ IP address of sip server
ONU (GPON): Enable or disable the SIP penetration firewall function.

Pincode
Management
RESTORE FACTORY SETTINGS: All the settings are restored to the factory settings. The IP address will be changed to the default IP: 10.1.1.2.
Operation
1W Panel
The mode of associate concierge is to disable Monitoring or NIGHT, Visitor push the pushbutton for calling in the 1W Panel, the ring back tone will be sent, countdown time in the monitor from 30s meanwhile the monitor will ring. The monitor will show video and can conversation after answer, then release lock.
The mode of associate concierge is to enable Monitoring, Visitor push the pushbutton for calling in the 1W Panel, the ring back tone will be sent, countdown time in the monitor from 15s meanwhile the monitor will ring. The monitor will show video and can conversation after answer, then release lock, the calling will transfer to concierge if the monitor doesn’t answer or doesn’t release lock.
The mode of associate concierge is DAY, Visitor push the pushbutton for calling in the 1W Panel, the ring back tone will be sent, the call will transfer to concierge.
The Concierge can transfer the call from 1W panel.
Block panel
The panel will call concierge when the visitor pushes the pushbutton, the panel send special sound if the concierge with NIGHT mode or general concierge enables ONLY RECEIVE.G.E. PANESL CALLS.
The panel can call concierge with other mode.
The Concierge can transfer the call from block panel.
General entrance panel
The panel will call concierge when the visitor pushes the pushbutton, the panel send special sound if the concierge with NIGHT mode.
The panel can call concierge with other mode.
The Concierge can transfer the call from block panel.
Installation and diagrams
Flush box installation

Installation guide diagram
-
Flush installar
-
Base flush box depth adjustment hook.
-
The upper part of the panel is stuck in, then move the panel to the flush box.
-
Move the slider of the panel and fix the two screws, when installing, pay attention to the reservation of the 1.7CM space around the door to move the slide cover.

Connector
The 1W PANEL is connected to the installation by means of connectors: Ethernet for LAN connection and MOLEX type connectors for other connections (power supply, RS-485, etc.). A bag containing the corresponding female connectors with their cables comes with the panel.

POWER INPUT: 12 Vdc power supply for the cases where no LAN PoE is available.
OUTPUT: Electric lock control relay output.
- NC: Normally closed contact
- NO: Normally opened contact
- C: Common
Exit Button / Door Sensor.
- (EXIT, -) Connections for indoor button
- (DS, -) Connection for door opened sensor
RJ 45 Network
- RJ-45 LAN or LAN PoE connection
NOTE:
Installing a door open sensor in DS, an alarm sounds in the panel and concierge if the door remains opened during 120s.
The panel has an internal tamper button. If the panel is separated from the wall, an alarm is triggered in the panel, concierge (if exists).
Tamper installation
Firmware updates
RTSP Streaming from outdoor panel
Regulation
FERMAX ELECTRÓNICA, S.A.U. declares that this product complies with the requirements of:
RED 2014/53/EU Directive “Radio frequency equipment”
Radio frequency module:
• Frecuencia: 13.56MHz / Potencia máxima: 2,45mW
Download Article
Table of Contents